Can I Set Up a Bathtub Myself? Factors to Consider As Well As Steps
Can I Set Up a Bathtub Myself? Factors to Consider As Well As Steps
Blog Article
How do you feel when it comes to Tools You Need to Install a New Bathtub ?
Setting up a bath tub isn't precisely rocket science, however it does require strong plumbing, carpentry, as well as sometimes, tiling abilities. Replacing an old tub with a brand-new one is likewise a reasonably challenging task. If the old tub is conveniently available, the job can relocate rapidly; if you need to open a wall surface to get rid of the old tub and also position the brand-new bathtub, the task is a lot harder. In either case, the job is within a residence handyman's skills, although you will certainly need a helper to vacate the old tub and set in the brand-new one. Make sure you have certified yourself for the task and also are comfortable attempting it. As opposed to hiring a professional to take over a halfway-completed task, it is better to think about utilizing one prior to you begin. Possibilities are you might require a professional plumber to make tube connections.
This write-up will assist you set up a brand-new bathtub in your restroom if you have currently acquired a new tub as well as do not require to transform the arrangement of your previous supply of water pipes.
Your devices and also product checklist ought to make up the following:
Planning for the Installation
Firstly, the supporting frame supplied with the bath must be fitted (if needed) according to the supplier's guidelines. Next off, fit the faucets or mixer to the bath tub. When suitable the tap block, it is important to ensure that if the faucet features a plastic washing machine, it is fitted between the bath and the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets device to prevent strain on the bathtub.
Fit the flexible faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (occasionally provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink outlet hole, and then pass the outlet through the hole in the bathroom. Make use of the nut provided by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next, fit the end of the adaptable overflow pipeline to the overflow electrical outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. See to it you make use of every one of the provided washers.
Connect the catch to the bottom of the waste electrical outlet on the tub by winding the thread of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bathroom must now be ready to be suited its last setting.
Removing Old Taps
If you require to change old taps with new ones as a part of your installment, then the first thing you need to do is detach the supply of water. After doing so, activate the taps to drain any type of water remaining in the system. The procedure of eliminating the existing faucets can be rather bothersome due to the limited gain access to that is typically the case.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that attaches the supply pipelines to the taps. Have a towel prepared for the remaining water that will certainly come from the pipelines. When the supply pipes have actually been eliminated, make use of the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary taps from transforming throughout this process. As soon as the taps have actually been removed, the holes in the bath/basin will need to be cleaned of any old securing compound.
Before going on to fit the new faucets, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the new faucets, after that a shank adapter is needed for the new faucets to fit.
Mounting the Bathtub
Utilizing both wooden boards under its feet, put the bath tub in the required setting. The wood boards are useful in uniformly spreading out the weight of the bathtub over the area of the boards as opposed to concentrating all the weight onto four little factors.
The next goal is to make sure that the bath tub is leveled all round. This can be attained by checking the spirit level and changing the feet on the tub up until the spirit level checks out degree.
To mount taps, fit the bottom of the outermost versatile faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the same for the other faucet.
Activate the water supply and check all joints and brand-new pipework for leakages and also tighten them if necessary. Fill the bathtub and likewise examine the overflow electrical outlet and also the normal outlet for leaks.
Ultimately, fix the bath paneling as described in the manufacturer's instruction manual. Tiling and also securing around the bath tub needs to wait till the tub has been made use of at the very least when as this will settle it into its final position.
Fitting New Taps
If the tails of the new taps are plastic, then you will need a plastic connector to prevent damages to the string. One end of the adapter fits on the plastic tail of the faucet and the other end offers a connection to the existing supply pipelines.
If you require to fit a monobloc, after that you will certainly call for lowering couplers, which links the 10mm pipeline of the monobloc to the standard 15mm supply pipe.
Next, place the faucet in the placing hole in the bath/basin guaranteeing that the washers are in location in between the faucet as well as the sink. Safeguard the tap in place with the maker given backnut. Once the tap is firmly in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by using corrugated copper piping or with normal tap connectors. The former kind needs to be connected to the faucet finishes initially, tightening up only by hand. The supply pipelines can later be attached to the various other end. Tighten up both ends with a spanner after both ends have actually been connected.
Tiling Around the Bathtub
In the area where the bathroom meets the tile, it is necessary to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture a stiff seal, causing the water to permeate the wall in between the bath as well as the tiling, resulting in difficulties with dampness and also possible leakages to the ceiling below.
You can select from a variety of coloured sealers to assimilate your fixtures and also fittings. They are marketed in tubes and cartridges, and can sealing voids as much as a size of 3mm (1/8 inch). If you have a larger gap to fill up, you can fill it with spins of soaked paper or soft rope. Remember to constantly fill the bath tub with water prior to sealing, to enable the movement experienced when the bathtub is in use. The sealer can break rather early if you do not take into account this movement prior to sealing.
Conversely, ceramic coving or quadrant ceramic tiles can be used to border the bath or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are likewise easily readily available on the marketplace. It is a good idea to fit the tiles utilizing water-resistant or water-proof adhesive and also grout.
How to Install a Freestanding Bathtub?
Installing a freestanding bathtub or any kind of bathtub is not a difficult task if you have a sophisticated guide on installing a freestanding bathtub in your bathroom. Aside from getting the freestanding bathtub to your bathroom, you can do all the work without paying a plumber. A bathroom with a bathtub is a retreat where you can feel the sensation of coming home and soaking in that hot water. It is a great way to remove all the stress from your day.
This guide will walk you through installing a freestanding bathtub in simple steps and help you find relief.
Slope
Make sure your bathroom has a proper slope. If your floor lacks a slope, the water flow to the drain will not function, which leads to a blocked drain which can cost you money. You can use the level device to see your bathroom's vertical and horizontal aspects. Once you have that information, you must carry out the next step.
Placement
A freestanding bathtub has a unique characteristic that helps you bring elegance to your bathroom. A freestanding bathtub comes in various sizes and shapes suitable for different types of bathrooms.
According to the information you gathered from the level device, you must pick a bathtub that suits your style and fits your bathroom aesthetically. You can place a freestanding bathtub virtually anywhere, such as in the corner, near the wall, or even at the center of your bathroom. However, you must ensure proper plumbing where you want to install the tub. If not, then you must call a plumber.
Clean the bathroom floor
After deciding where to place the bathtub, you must clean the entire bathroom floor so that the dust and debris do not accumulate underneath the tub. Simple cleaning is enough, and you will clean it again after the installation.
Steps to Install a Freestanding Bathtub:
STEP 1: Place the protective blanket in the adjacent area where you want to install the bathtub. It will help you protect the bathtub's sides when you do the installation.
STEP 2: Now, place the 4x4 lumber in the area where you want to install the bathtub. Place the bathtub on top of the lumber, and align the drain line with the bathtub drain.
STEP 3: A freestanding bathtub comes with a drain kit. If not, make sure you purchase one with your bathtub. You can pop that drain kit and align it with your bathroom drain line. Ensure that you tighten the drain nut enough so there is no water leakage. You must also clean the bathtub’s drain to remove the factory dirt and debris.
STEP 4: Clean the drain hole in your bathroom. It helps to do the installation without any water blockage. A drain cleaner or bleach will suffice. Once the drain dries entirely, take a small amount of clear silicon and place it around the underside of the pipe flange.
STEP 5: Attach the drain tailpiece to the bottom of the bathtub. Place the rubber or plastic bushing with the plumbing material at the top of the tailpiece and screw the drain nut up the tube until it tightens both the bathtub’s drain and the drain tailpiece. Now you must add the lubricant to the seal to ensure there is no water leakage in the pipe connection.
STEP 6: Place caulk around the bottom edge of the bathtub. Take out the lumbar support and carefully bring the bathtub to the floor. Use a damp cloth to clean the excess caulk and debris and plumber putty to cover the tub drains and the floor.
Tips to Maintain a Freestanding Bathtub:
Always look for the clog in the drain. You can pull it out with a small stick if hair or debris is in the gutter. Use mild cleaning components, which will help you preserve the bathtub for a long time and will also help you remove surface-level scratches. Do not use strong solutions such as concentrated bleach to remove stains. Instead, mix water and diluted bleach with a ratio of 10:2, respectively. Apply it to the tub's surface and leave it for 15-20 minutes to remove any surface-level stains. Always check the floor drain. You may unclog it using any small sticks or a small vacuum to suck out all the debris. Check the heater or faucet immediately if you smell rust or grease in the water. Rust in the water may stain or damage the bathtub in the long run. If you want to sand the bathtub, try using 400 grit sandpaper or 600 grit sandpaper for a more refined finish.
We hope you enjoyed reading our excerpt on How to Install a Bathtub Yourself. Thank you for spending some time to browse our post. Do you know about somebody else who is interested in the niche? Take a moment to promote it. Thanks a lot for taking the time to read it.
Schedule Estimate
Report this page